Référence: H102691
Price incl. VAT: €109.95
Molloplast B is a heat-curing, one-component silicone designed as a permanent soft relining material for dentures made from (meth)acrylate-based denture acrylics. It provides a shock-absorbing, elastic and comfortable interface with the oral mucosa, particularly suitable for patients with thin ridges, sharply contoured alveolar processes or sensitive soft tissues.
For use by dental professionals only (dental laboratories and dental practices).
Molloplast B converts a rigid denture base into a soft, cushioning and tissue-friendly interface. The heat-curing silicone formulation ensures permanent softness and resilience, while the smooth, non-porous surface helps to limit plaque accumulation and facilitates routine cleaning of the denture.
Molloplast B is indicated for:
The material is intended for professional use in dental laboratories or dental practices equipped for flask processing and heat-curing techniques.
Thoroughly clean, disinfect, degrease and prepare the acrylic denture base (new or existing). Remove any old soft liner or reline material completely. Roughen the surface according to the manufacturer’s instructions, then apply the Detax-recommended adhesive/primer to all areas to be relined and allow it to dry completely (approx. 60–90 minutes) before packing the flask.
Place the denture in a properly insulated flask using a suitable investment material. After the adhesive has dried, evenly load all relining areas with Molloplast B. Close the flask under adequate pressure to avoid air entrapment and to express excess material. Remove the excess material from the borders before polymerization.
Polymerize strictly in accordance with the Detax instructions for use. Typical parameters:
Ensure controlled and homogeneous heating. At the end of the cycle, allow the flask to cool slowly and completely to room temperature before opening in order to minimize internal stresses and prevent deformation of the denture base.
After deflasking, finish the acrylic parts using conventional instruments. For Molloplast B surfaces, use burs and polishers specifically designed for soft silicones, with light pressure and adequate cooling to avoid overheating and debonding. Mechanical high-gloss polishing of the silicone is limited; if a higher surface gloss is desired, use a suitable surface conditioner or polish recommended by the manufacturer. Aim for a smooth, homogeneous surface for optimum patient comfort and hygiene.
Always refer to the official Detax Instructions for Use for precise parameters, contraindications, safety information and detailed processing guidelines.
Pressure curing of resins and soft relines for homogeneous polymerization without porosities.
Flask dedicated to microwave curing cycles, ideal for rapid polymerization of Molloplast B.
Powerful, controlled flask pressing for uniform, bubble-free packing of Molloplast.
A few best practices to optimize your permanent soft relines with Molloplast B:
For repair or secondary relining of an existing Molloplast layer, remove approximately 1 mm of the old material, prepare the surface again, re-apply the adhesive and proceed with packing and polymerization according to the Detax instructions. This maintains optimal bonding between the new and existing silicone layers.
| Material type | Heat-curing, one-component silicone Permanent soft relining material for denture bases |
|---|---|
| Main indication | Permanent soft relining of complete or partial dentures made from (meth)acrylate acrylic resins |
| Compatibility | Conventional (meth)acrylate denture base resins (new dentures and existing dentures to be relined) |
| Polymerization | Water bath: approx. 2 h at 100 °C in a suitable flask Microwave: approx. 10 min at 850 W using a microwave-compatible flask (no metal parts) |
| Properties | Permanent softness and resilience, excellent bonding when used with the recommended adhesive, smooth and hygienic surface, limited mechanical high-gloss polishing of the silicone (use suitable silicone polish if higher gloss is required) |
| Packaging | Jar of Molloplast B permanent soft liner (commercial reference SKU H102691) |
| Manufacturer | Detax |
| Intended use | Restricted to dental professionals (dental laboratories and appropriately equipped practices) |
Molloplast B Detax is supplied in secure, tamper-evident packaging with labelling compliant with medical device regulations. Store at stable room temperature, protected from excessive heat, direct sunlight and humidity.
Always check the expiry date before use and follow the manufacturer’s safety and processing instructions. Processing must only be carried out by personnel trained in permanent soft relining techniques and in the use of heat-curing silicones.
Molloplast B is designed as a permanent soft relining material for complete and partial dentures made from (meth)acrylate denture base resins.
Yes. Unlike temporary soft reline materials, Molloplast B is a permanent soft silicone liner.
The material is intended for conventional denture base resins based on (meth)acrylate.
Yes. The use of the Detax adhesive/primer is critical to ensure a durable chemical bond between Molloplast B and the acrylic denture base.
Yes, repairs and secondary relines are possible on an existing Molloplast B lining.
Molloplast B Detax – Permanent Soft Relining Material for Dentures
